LOAD GENIE MARK II LGM 20 SERIES |
|
- Application: Self Contained Unloading Valve
Can Be Used Wherever a Continuous Run Air Compressor Is Required
- Combines All Components Required for Continuous Run Compressors: Pilot Valve, Vent Valve and Check Valve
- Eliminates the Need for Built in Head Unloaders
- Easy Installation: Install the Mark II in the Discharge Line Between the Compressor and the Air Receiver
- Factory Preset
Cut In : Cut Out: Pressure (Standard) 95 – 115
(Optional High Pressure) 145 - 175
Minimum Cut In: 60 PSI
Maximum Cut Out: 250 PSI
Can be Field Adjusted
- Construction: Forged Brass Body, Brass & Zinc Plated Steel Internal Components, Stainless Steel Springs and Glass
Filled Fluoropolymer Poppet
- Tapped & Plugged 1/8” Port for Throttle Control of a Gas Engine
- 1/8” NPT Tapped Port for Pressure Switch Unloader Valve and Vent Port Muffler
- A Toggle Unloading Lever for One Hand Warm Up Control
- Suitable for Compressors Up to 20 SCFM
- Optional 3/8 Muffler M20053
- 1/2” FPT Port
|
LOAD GENIE MARK III LGM 30 SERIES |
|
- Application: Self Contained Unloading Valve Can Be Used Wherever a Continuous Run Air Compressor Is Required
- Combines All Components Required for Continuous Run Compressors: Pilot Valve, Vent Valve and Check Valve
- Eliminates the Need for Built in Head Unloaders
- Easy Installation: Install the Mark III into the Receiver and Attach the Compressor Discharge Line to the Valve Inlet
- Factory Preset
Cut-In : Cut-Out: Pressure (Standard) 95 – 115
(Optional High Pressure) 145 - 175
Minimum Cut- In: 60 PSI
Maximum Cut- Out: 250 PSI
Can be Field Adjusted
- Construction: Forged Brass Body, Zinc Plated Steel Internal Components
Fluorocarbon Piston Ring, Stainless Steel Springs and a Glass Filled
Fluropolymer Check Valve Poppet
- Tapped & Plugged 1/8” Port for Throttle Control of a Gas Engine
- 1/8” NPT Tapped Port for Pressure Switch Unloader Valve and Vent Port Muffler
- A Toggle Unloading Lever for One Hand Warm Up Control
- Suitable for compressor Up to 30 SCFM
- Equipped with M20053 3/8” Muffler
- Optional Inlet and Outlet Ports Available— Consult Price List
|
LOAD GENIE MARK IV LGM 40 SERIES |
|
- Application: Self Contained Unloading Valve Can Be Used Wherever a Continuous Run Air Compressor Is Required
- Combines All Components Required for Continuous Run Compressors: Pilot Valve, Vent Valve and Check Valve
- Eliminates the Need for Built in Head Unloaders
- Easy Installation: Install the Mark IV into the Receiver and Attach the Compressor Discharge Line to the Valve Inlet
- Compact Design Incorporates Both a Straight (LGM40A) & Optional 90 Degree Inlet (LGM40C) Flow Design
- Factory Preset
Cut- In: Cut- Out: Pressure (Standard) 95 – 115
(Optional High Pressure) 145 - 175
Minimum Cut- In: 60 PSI
Maximum Cut- Out: 250 PSI
Can be Field Adjusted
- Construction: Forged Brass Body, Zinc Plated Steel Internal Components Fluorocarbon Piston Ring, Stainless Steel Springs and a Glass Filled Fluropolymer Check Valve Poppet
- Tapped & Plugged 1/8” Port for Throttle Control of a Gas Engine
- 1/8” NPT Tapped Port for Pressure Switch Unloader Valve and Vent Port Muffler
- A Toggle Unloading Lever for One Hand Warm Up Control
- Suitable for compressor Up to 30 SCFM
- Equipped with M20053 3/8” Muffler
- Optional Inlet and Outlet Ports Available— Consult Price List
Model No. |
Dimensions
(A) |
Dimensions
(B) |
Dimensions
(C) |
Dimensions
(D) |
LGM-20 |
3.87 |
1.43 |
.81 |
4.31 |
LGM-30 |
3.28 |
1.65 |
2.10 |
2.21 |
LGM-40 |
4.07 |
2.41 |
|
|
|
